ioBroker.tesla-wallconnector3

Tests:

tesla wall connector gen 3 adapter for ioBroker

Dokumentation DE
Documentation EN

Targeted at the Tesla Wall Connector Gen 3 available at https://shop.tesla.com/de_de/product/gen-3-wall-connector . Only provides read access to API data (write isn't supported by the API).

Installation

You can install the adapter via the ioBroker web interface.

1. Open your ioBroker web interface in a browser (eg: 192.168.178.42:8081)
2. Click on Tab "Adapters"
3. Type "tesla-wallconnector3" in the filter
4. Click on the "+" symbol of the Tesla Wall Connector Gen 3 adapter

Setup

Additional to the adapter installation you have to add an instance of the adapter.

ioBroker

1. Open your ioBroker interface in a browser (eg: 192.168.178.42:8081) (if configuration dialogue was opened automatically after installation, skip to 4.).
2. Navigate to Tab "Instances"
3. Click on the wrench symbol of the Tesla Wall Connector Gen 3 adapter
4. Now you can see the main settings of the adapter configuration page.
   4.1 Type in the IP-address of your Tesla Wall Connector Gen 3 (FQDN is also possible if you have a working local DNS).
   4.2 You can change the polling interval, too. (Default: 10 seconds)
   4.3 If your network requires a higher timeout for requests sent to Tesla Wall Connector Gen 3, please change the Request-Timeout in miliseconds accordingly. (Default: 5000 miliseconds)
   4.4 In case there is an issue communicating with Tesla Wall Connector Gen 3 the adapter will retry several times. You can adjust how often it will try to read from Tesla Wall Connector Gen 3. (Default: 10)
   4.5 To space retries apart a bit more you can adjust the Polling Retry Factor. (Default: 2)
   Example: Using default settings the 1st retry will happen 20 seconds after the initial try, the 2nd will happen 40 seconds after the 2nd try.
   After each successful connect to Tesla Wall Connector Gen 3, the number of retries is reset.
5. Click on Save & Close

Usage

Here you can find a description of the states and how to use them. All states of this adapter are read-only states.
Please be aware that most (if not all) descriptions might be way off and might require confirmation or corrections. Pull-Requests with updates are welcome and encouraged!

Known States

Channel: info

• info.connection

  Data type	Permission
  boolean	R

  Read-only boolean which is true if the adapter is connected to the Tesla Wall Connector Gen 3.

Channel: lifetime

• alert_count

  Data type	Permission
  number	R

  Read-only number, representing the number of alerts.

• avg_startup_temp

  Data type	Permission
  number	R

  Read-only number, representing if the average startup temperature.

• charge_starts

  Data type	Permission
  number	R

  Read-only string, representing the number of charging starts.

• charging_time_s

  Data type	Permission
  number	R

  Read-only number, representing the charging time in seconds of the WC3

• connector_cycles

  Data type	Permission
  number	R

  Read-only number, representing the number of connector cycles (plugging in and out most likely counting each as 1).

• contactor_cycles

  Data type	Permission
  number	R

  Read-only number, representing the number of state-changes of the relais so far.

• contactor_cycles_loaded

  Data type	Permission
  number	R

  Read-only number, representing the number of charging cycles.

• energy_wh

  Data type	Permission
  number	R

  Read-only number, representing the amount of energy supplied in Wh.

• thermal_foldbacks

  Data type	Permission
  number	R

  Read-only number, representing the ???

• uptime_s

  Data type	Permission
  number	R

  Read-only number, representing the uptime in seconds of the WC3

Channel: version

• firmware_version

  Data type	Permission
  string	R

  Firmware version on the Tesla Wall Connector Gen 3

• part_number

  Data type	Permission
  string	R

  Part number of the Tesla Wall Connector Gen 3

• serial_number

  Data type	Permission
  string	R

  Serial number of the Tesla Wall Connector Gen 3

Channel: vitals

• current_alerts

  Data type	Permission
  string	R

  Read-Only string with details about alerts.

• contactor_closed

  Data type	Permission
  boolean	R

  Read-Only boolean indicating if the relais is closed.

• grid_hz

  Data type	Permission
  number	R

  Read-Only number representing the grids frequency.

• config_status

  Data type	Permission
  number	R

  Read-Only number representing the config status. Please help with details!

• current[A,B,C,N]_a

  Data type	Permission
  number	R

  Read-Only number representing the current of line [A,B,C,N] in ampere.

• evse_state

  Data type	Permission
  number	R

  *Read-Only number representing the evse state. We seem to know so far: 0=booting, 1=idle, 2=connect but not ready, 3=???, 4=connected and ready, 5=???, 6=vehicle plugged in and handshaking, 7=???, 8=charging completed/interrupted, 9=ready for charging but waiting on car, 10=charging with reduced power (less than 3 phases, 16 amps each), 11=charging full power (3 Phases, 16 amps each), 12=??? *

• grid_v

  Data type	Permission
  number	R

  Read-Only number representing the grids voltage.

• handle_temp_c

  Data type	Permission
  number	R

  Read-Only number representing the handle's tempearture in °C.

• input_thermopile_uv

  Data type	Permission
  number	R

  Read-Only number representing ???.

• mcu_temp_c

  Data type	Permission
  number	R

  Read-Only number representing the master control unit's tempearture in °C.

• pcba_temp_c

  Data type	Permission
  number	R

  Read-Only number representing the printed circuit board's tempearture in °C.

• pilot_high_v

  Data type	Permission
  number	R

  Read-Only number representing the pilot line's high voltage.

• pilot_low_v

  Data type	Permission
  number	R

  Read-Only number representing the pilot line's low voltage.

• prox_v

  Data type	Permission
  number	R

  Read-Only number representing ???.

• relay_coil_v

  Data type	Permission
  number	R

  Read-Only number representing the relay coils voltage.

• session_s

  Data type	Permission
  number	R

  Read-Only number representing the duration of the current charging session in seconds.

• session_energy_wh

  Data type	Permission
  number	R

  Read-Only number representing the energy supplied in the current session in Wh.

• uptime_s

  Data type	Permission
  number	R

  Read-Only number representing the WC3's uptime in seconds.

• vehicle_connected

  Data type	Permission
  boolean	R

  Read-Only boolean indicating if a vehicle is connected.

• vehicle_current_a

  Data type	Permission
  number	R

  Read-Only number representing vehicles current in ampere.

• voltage[A,B,C]_v

  Data type	Permission
  number	R

  Read-Only number representing the voltage of line [A,B,C].

Channel: wifi_status

• internet

  Data type	Permission
  boolean	R

  Read-only boolean, representing if the Tesla Wall Connector Gen 3 is connected to the internet.

• wifi_connected

  Data type	Permission
  boolean	R

  Read-only boolean, representing if the Tesla Wall Connector Gen 3 is connected to wifi.

• wifi_infra_ip

  Data type	Permission
  string	R

  Read-only string, representing the IP of the Tesla Wall Connector Gen 3.

• wifi_mac

  Data type	Permission
  string	R

  Read-only string, representing the MAC address of the Tesla Wall Connector Gen 3.

• wifi_rssi

  Data type	Permission
  number	R

  Read-only number, representing the rssi of the wifi the Tesla Wall Connector Gen 3 is connected to.

• wifi_signal_strength

  Data type	Permission
  number	R

  Read-only number, representing the signal strength of the wifi the Tesla Wall Connector Gen 3 is connected to.

• wifi_snr

  Data type	Permission
  number	R

  Read-only number, representing the snr of the wifi the Tesla Wall Connector Gen 3 is connected to.

• wifi_ssid

  Data type	Permission
  string	R

  SSID the Tesla Wall Connector Gen 3 is connected to.

Changelog

1.0.6 (NoBl)

• Maintenance update (dependencies, ...)

License

MIT License

Copyright (c) 2024 Norbert Bluemle [e-mail]

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.